EasyStand Bantam Owner's Manual

Owner’s ManualMedium

13. Remove the two covers on the hip pivot of the back. There are three small bolts to remove on each cover, set covers and bolts aside, these will be

16. Line up the holes and place the plastic washer between the back and the slot on the seat, insert bolt from the inside of the unit. Do the same on

19. If the Pow’r Up Lift option was ordered, insert bolt onto the bracket on the side of the unit. 20. Install the controller by assembling as shown.

22. Replace the top bolt and the bolt on the backside and tighten securely, the third bolt will be installed later. 23. Lock casters, with assitance,

25. Insert all 4 bolts into the base and wheel assembly, make sure to start all 4 bolts, then tighten securely.26. Place both foot plates on the unit,

28. Place the unit back on to its wheels, remove the nuts from the Supine controller bracket. 29. Place the controller and hardware onto the unit. D

31. If the optional Shadow Tray was ordered, loosen the ratchet handles on the side of the tray, flip the arms up and tighten the ratchet handles. Lock

34. Make sure the swivel collar is placed onto the tube insert. Place the collar onto the frame until the plunger locks into place. The plunger handle

37. Place the tray assembly bracket into the H-Frame.38. Depress the spring button to allow the bracket to slide into the H-frame (A). Once the clamp

40. If a Head Support was ordered, loosen the knob and insert Head Support, tighten securely.41. Insert each knee pad assembly into the tube along the

SYMBOL LEGEND!CAUTION/ATTENTIONPINCHPOINTSERIAL NUMBERSNENVIRONMENTALCONDITIONSDATE OF MANUFACTUREPlease be environmentally responsible and recycle th

43. Attach the pump handle to the pump on the seat assembly with bolts and nuts, tighten securely. Insert top of handle into pump handle and tighten b

Seat Depth Adjustment1. Prior to adjusting seat depth, make sure the Controller is in the “Sit-to-Stand” position. The seat should be lowered to a sea

Controller UsageDesigned with ease of use and the safety and comfort of the user in mind, the Controller as shown is the single point of operation for

Controller UsageNeutral Mode8. By lifting the safety collar and rotating the shift knob into Neutral position, the footrest carrier and backrest (whic

Controller UsageSupine ModeCaution: A properly fitted and adjusted headrest MUST be used with the supine option.The Bantam Medium with Supine Option fu

Shadow Tray Adjustment12. To adjust tray depth, loosen each knob as shown all the way loose. Then flip the red plunger lever in the cen-ter of each kno

Shadow Tray Adjustment16. To adjust the tray height, loosen both knobs on the back of the unit and set to desired position. Tighten knobs securely.Bac

Head Support Adjustment20. To adjust the head support height, loosen the knob on the back of the back option, move to desired position and tighten sec

Charging the BatteryThe EasyStand Bantam Medium Pow’r Up Lift uses two 12-volt sealed lead batteries rated at 2.9 amps each. An EasyStand Bantam Mediu

CAUTION: Using the emergency mechanical release as the primary means of returning to the seated position can cause damage to the unit. Only use the me

Table of ContentsIntroduction ...1Safety Precautions ... 2Assembly ...

Guidance and Manufacturer’s Declaration - Electromagnetic EmissionsThe EasyStand Bantam Medium is intended for use in the electromagnetic environment

Guidance and Manufacturer’s Declaration - Electromagnetic ImmunityThe EasyStand Bantam Medium is intended for use in the electromagnetic environment s

Recommended separation distances between portable and mobile RF communications equipment and the EasyStand Bantam MediumThe EasyStand Bantam Medium is

Options & Parts DetailOptions & Parts DetailPage 30

Cleaning/Disinfecting • Clean the EasyStand with a mild, non-abrasive disinfectant or soap and water.• Check the EasyStand at least weekly to ensu

Limited WarrantyThis warranty is extended only to the original purchaser/customer (or supplier non consumer who does not buy or resell). Altimate Medi

Standing technology should only be used under the guidance of a physician with recommendations for standing program protocol and any medical precautio

IntroductionCongratulations on your purchase of the EasyStand Bantam Medium standing frame! We at Altimate Medical have designed the EasyStand Bantam

• Please read and understand all safety precautions and user instructions prior to use. Call Altimate Medical at 800-342-8968 or 507-697-6393 with

1. The base model consists of the front frame, no-tray assembly, pump handle, seat assembly, knee pads and foot plates.2. Position the unit as shown t

4. Place metal washer onto the stud of the caster.5A. Place the caster onto the unit as shown.5B. Place the black cupped washer onto the caster stud.6

7A. Place the lock nut onto the caster stud and tighten securely using provided wrench.7B. Place black cap onto the unit to cover hardware.Repeat thes

10. Turn the knobs all the way loose, flip the red tab of the knobs to the open position on both following arms.11. Insert both following arms onto the