EasyStand Bantam Owner's Manual

Owner’s ManualExtra Small & Small

13. Loosen the ratchet handles on the foot plates and swivel into place (for information on foot plate adjustments see pg. 14).14A. Insert

16. Remove knob and metal washer from the knee pad, leaving the rubber washer in place on the knee pad, place the knee pad and rubber wa

AB19. Place the tray upside down, remove the knob, nut, and washers from both tray slides and set aside. Place the tray bracket onto the bolts

AB22. Depress the spring button to allow the bracket to slide into the H-frame (A). Once you clear the clamp the spring button needs to be de

26. Place the back in the desired position. Insert knob and tighten securely.27. If you ordered only the optional headrest, insert the head su

Mobile Option AssemblyNote: If this is an option added after the initial purchase, you must remove the existing front assembly before proceeding.1.

4. Attach the interchangeable right and left drive wheel assemblies to the front frame. 5. Line up the holes and tap in the coved nuts and tig

FIG. AHeight FIG. BPlantar/DorsiFIG. CAdductionFIG. DForward/AftKneepadsFIG. G-The standard knee pads have depth and pad rotation adjustments only. To

Seat Depth/Back Angle/Back HeightCaution: Do not adjust the seat depth while the child is in the unit.Caution: Ensure the colors on the seat tube and

Push Handle Mounting HolePush Handle Mounting HoleChest Vest Top Mounting HoleHeadrest Mounting Holes Chest Vest TopMounting HoleChest Vest Bottom Mou

SYMBOL LEGEND!CAUTION/ATTENTIONPINCHPOINTSERIAL NUMBERSNENVIRONMENTALCONDITIONSDATE OF MANUFACTUREPlease be environmentally responsible and recycle th

Supine Option Usage1. Loosen both red supine locking handles located by the hip pivot on both sides of the unit. Flip the supine lever located

1. Flip the supine lever located under the right side of the seat to the “sit to stand” position.2. Loosen the red locking handles. Handles

Charging the BatteryThe EasyStand Bantam Pow’r Up Lift uses two 12 volt sealed lead batteries rated at 2.9 amps each. An EasyStand Bantam can be lifte

FIG. DFIG. CFIG. EFIG. FAssembly of the Hand ControlFIG. C-Remove hardware from hand control tube.FIG. D-Insert hand control tube into the side of the

CAUTION: Using the emergency mechanical release as the primary means of returning to the seated position can cause damage to the unit. Only use the me

Guidance and Manufacturer’s Declaration - Electromagnetic EmissionsThe EasyStand Bantam is intended for use in the electromagnetic environment specifie

Pow’r Up Lift OptionPage 23Guidance and Manufacturer’s Declaration - Electromagnetic ImmunityThe EasyStand Bantam is intended for use in the electroma

Recommended separation distances betweenportable and mobile RF communications equipment and the EasyStand BantamThe EasyStand Bantam is intended for u

Parts DetailPage 25EasyStand® Bantam Parts Detail

Cleaning/Disinfecting • Clean the EasyStand Bantam with a mild, non-abrasive disinfectant or soap and water.• Check the EasyStand at least weekly

Table of ContentsIntroduction ...1Safety Precautions ... 2Assembly ...

TroubleShootingTroubleShootingPage 27My lower leg length is too short for the stander. Invert and swap the foot plates left to right.My Bantam won’t g

WarrantyLimited WarrantyThis warranty is extended only to the original purchaser/customer (or supplier non-consumer who does not buy or resell). Altim

Standing technology should only be used under the guidance of a physician with recommendations for standing program protocol and any medical precautio

IntroductionCongratulations on your purchase of an EasyStand standing frame! We at Altimate Medical have designed the EasyStand with your comfort and

• Please read and understand all safety precautions and user instructions prior to use. Call Altimate Medical at 800-342-8968 or 507-697-6393 with

Assembly1. The basic stander consists of three assemblies. Options are in addition to the three assemblies. • Front Frame • Back • Seat Post / Re

4. Flip up the rear frame to allow easier access to the post. Attach the front and rear frames to one another.5. Place the two coved nuts in

7. Place the unit back in the normal position. Step on the gas spring assist pedal to raise the seat about 3/4 the way up as shown. 8. If the

10. Depress the spring button to allow the following arm to slide into place. Match the following arm position color with the corresponding sea